Recharge Guide for the Upgraded Shower Water Softener System
Once you’ve been using the system, you’ll notice the difference between hard and soft water by how “slippery” it feels in the shower. When the water no longer feels soft, simply use the included test strips to check the hardness. After you confirm hard water, follow our step-by-step recharge guide here.
- Mix 2.9 lb(1.3kg) of water softener salt with 1.4 gallons of water until fully dissolved. (Use SoftWaterCare recharge salt or water softener salt only. If using pellets, prepare the solution 2 to 3 days in advance to make sure the salt is fully dissolved.)
- Connect the recharge hoses and pump.
- Switch the valves to recharge mode.
- Circulate the salt solution for 4 to 5 hours, or simply let it run overnight. (This circulation method gives the resin enough contact time with the salt solution, helping it recharge thoroughly and maintain strong softening performance.)
- Disconnect the recharge setup and return the valves to shower mode.
- Run the shower for about 3 minutes to flush the system.
- Recharge complete. Ready for soft water again.
If you have any questions, feel free to contact us at service@softwatercare.com.
Recharge & Maintenance FAQ
1. Do I need to recharge before first use?
1. Do I need to recharge before first use?
No recharge needed at first! Just turn the valve on and let water flow through the system for about 3 minutes. You might see yellow water at the beginning—don’t worry, that’s completely normal. It means the resin is flushing out initial dust and particles from manufacturing, which confirms your system is brand new. After that, the water will run clear and soft.
2. What kind of salt should I use?
2. What kind of salt should I use?
You can use either of the following:
- Non-iodized table salt – dissolves quickly and is easy to use
- Water softener salt pellets – more affordable, but takes longer to dissolve
Tip: To speed up pellet salt, mix it with boiling water and wait 1–2 hours for it to dissolve. Be sure to let the water cool to room temperature before recharging.
3. What powers the pump? Can I plug it in?
3. What powers the pump? Can I plug it in?
The pump is powered via USB and is not designed to be plugged directly into a wall outlet.
Doing so is extremely dangerous and can damage the pump or cause serious safety issues.
Always use a portable USB power bank when recharging the system.
4. What if the pump stops working?
4. What if the pump stops working?
Sometimes during your second recharge, the pump may get stuck due to salt residue. Here’s how to fix it:
- Soak the pump in clean water for half a day or a full day.
- If it still doesn’t work, try opening the pump and soaking it again.
👉 Watch how to open the pump
To prevent this, rinse the pump with clean water after every recharge.
If soaking the pump doesn’t fix the issue, you can buy a replacement pump kit here.
To recharge the softener, we use a brine container and pump to circulate concentrated saltwater through the system.
Traditional softeners typically fill only half the space with resin, leaving the rest open for soaking in brine during recharge. While this works, it reduces space efficiency and lowers the initial soft water capacity. By moving the brine to a separate container for circulation, we maximize the space inside the softener, filling it with more resin to increase the initial soft water capacity. Additionally, brine circulation is a more efficient recharging method, resulting in a greater amount of soft water after each recharge.
To recharge the softener, we use a brine container and pump to circulate concentrated saltwater through the system.
Traditional softeners typically fill only half the space with resin, leaving the rest open for soaking in brine during recharge. While this works, it reduces space efficiency and lowers the initial soft water capacity. By moving the brine to a separate container for circulation, we maximize the space inside the softener, filling it with more resin to increase the initial soft water capacity. Additionally, brine circulation is a more efficient recharging method, resulting in a greater amount of soft water after each recharge.